How to Reduce or Prevent Condensation in Your Home

Condensation occurs when air hits a cold surface. Air has a limit to the amount of water it can hold in suspension and the amount of water in the air is known as the relative humidity (measured as a percentage). Once air becomes saturated, the relativity humidity has reached 100%. Now as the temperature becomes lower, air can hold less and less water. Condensation occurs when water laden air hits a cold surface, reducing the temperature of the air. This could be glass in windows, cold tiles or metal surfaces. These surfaces are either colder than other surfaces in a room or are of high thermal conductivity so that heat is sucked out of the air. In any case, the air temperature drops to the extent that it can't hold moisture any more and it is deposited on the surface.
To avoid condensation you have several options. Firstly you can vent moisture laden air (e.g from cooking in the kitchen) so that it doesn't end up in rooms. You can do this by using extractor fans or simply opening windows. Portable gas heaters produce lots of water vapour and should be avoided. Another option is to raise the temperature in the room. This makes surfaces warmer so that moisture doesn't condense out. Double or triple glazing also helps because the external surface of inner panes of glass is not in contact with air outside the house. Removing sources of moisture also helps. This includes house plants and damp clothing. Clothes in the washer should be kept there with the door closed until they are transferred to a drier, or hung outside. Drying clothes in rooms or on radiators transfers water to the air where it inevitably condenses out if windows are closed and the room temperature drops. Yet another way of reducing condensation is to use a dehumidifier. This appliance works by circulating air over chilled coils. This causes moisture to drop out of the air (just like it does on your windows) and collect in a reservoir tank.

How Can a Pinhole Leak be Temporarily Fixed Until a More Permanent Repair Can be Done?

Ordinary 2-part epoxy resin also works well for sealing leaks. I have used it successfully for repairing a long crack in the polystyrene spray nozzle of a hose. Make sure you get the quick setting stuff which hardens in about 10 minutes. Try and dry the joint thoroughly, and if possible, rub it with sandpaper to improve adhesion. Let the epoxy stiffen slightly before applying to prevent it spreading out. Heat from a hair drier accelerates the curing process. As far as I know special pipe sealants are epoxy based.
Another alternative (although this is theoretical and I haven't tried it!) is to use a hose clip. Keep one opened out and if you have a leak, wrap it around the pipe, push the end of the clip back into itself and semi-tighten it with a screwdriver. Push a small piece of rubber (bicycle patch, piece of old tire, rubber boot or whatever) under the clip over the hole and tighten. The advantage of this is that the water wouldn't have to be turned off and the area around the hole wouldn't need to be dry but it would probably only work on a hole in the actual pipe itself where the clip would exert sufficient pressure on the patch. You can also buy emergency clamp type fittings which seal over a hole, effecting a temporary repair until the section of pipe can be replaced.
Yet another repair method for cracked brass fittings is to solder them. I had to do this when a fitting on a heating system in my workshop developed a hairline crack during a lengthy period of snow during the winter. (Haven't looked at it for years so hopefully it's still water tight!).
It's wise to know the location of all your stop cocks/gate valves, and write the function of the valve on the wall behind it with a marker, or tie a label around it. In an emergency, you don't want to have to figure out which valve shuts off which pipe. Also valves tend to stick and seize up after years of disuse, so "exercise" them at least once a year by screwing off and back on again. It's actually a good a wise idea to add a redundant valve in case your main water shut-off valve fails. Another option is to fit a quadrant ball valve in addition to the main valve which can be quickly turned off by turning it through 90 degrees (These are the ones commonly encountered on gas and air compressor lines or on oil tanks). Quadrant valves don't normally seize up.